A small happy face logo and a Welcome message greet new users. The BT 50 has a power off feature, which I've found missing from many other regulated devices. I did notice some residual machining artifacting but nothing incredibly obvious.įive clicks turns on the device yes, you did read that right. The cover fits in either direction, but with the Smok logo printed at the bottom, I figure most will only mount it in that specific orientation.
#Smok xpro bt50 mod
The mod is designed for flat top cells and as mentioned, the fit is snug so there is no battery play at all. A nice touch, the holder is mounted positive side down, in line with the bottom vent hole. The holder's fit is snug and the inclusion of the cell removal ribbon is appreciated. The interior layout of the mod is very clean, with a covered electronics section and a well finished battery holder. As the case is not meant to be opened regularly, this is somewhat of a moot point.
#Smok xpro bt50 registration
The advantage to this is the increased level of adjustability in door fit, but could have been entirely mitigated by the use of grooved registration to centre the door to the case and partially hold it in place. The case cover lacks any kind of registration slots, grooves or pins and must be held in place to screw on and off. I would have appreciated a magnetic case door system but can accept that screws are an acceptable solution, especially when they are high quality stainless steel, knurled hex head screws. Using the provided hex key, I opened the case. The countersunk well is about 2mm deep and will accept 23mm atomizers. Spring-loaded, it has accepted every single atomizer I've thrown at it without a single issue! As no air slots are provided, bottom aerated atomizers could encounter some issues. The top plate includes a countersunk atomizer mount point, with one of the best 510 connectors I've experienced. The charge port and the venting hole are located on the bottom of the case, somewhat inconvenient in terms of charging but logically located in terms of venting safety. They have a positive feel, decent click and tolerable sound level! There is some slight rattle from the buttons, as they are metal in a metal enclosure and to be expected. The case is beveled on the top and bottom planes, reminiscent of the iPhone or iPad in that design element. The empty mod is fairly light and the finish is slightly pebbled anodizing, which provides a less slippery surface than the usual treatment. I took a few moments to look over the device. A little disappointed to find a rather mediocre quality micro usb cable, a tiny hex key and a small booklet.
#Smok xpro bt50 free
Once opened, the device is easy to slip out, leaving the tray free to be lifted. The Xpro BT 50 comes in a well packaged plastic shell, with fitted foam, although a little large in terms of packaging. Although it's offered in several colors, I picked up a silver one as it was exactly what I was looking for. Welcome to contact us anytime to get help.I had been looking for a box mod for a while and when the Xpro BT 50 came out at my local vape shop, Sir Vape A Lot, I decided that I would pick one up. please have a basic knowledge of batteries. the device always recommends work with rechargeable lithium-ion IMR batteries with a min output current of 20A or higher.Ģ) Smokstore will not responsible or liable for any injury, damage, defect, permanent or temporary that may be caused by the improper use of Li-ion battery, coils, tanks, mods. we will not responsible for damage for human reasons or mishandling of Li-ion batteries and chargers. please use the fire-proof surface battery charger, never leave the charging battery unattended. so vapers must have enough knowledge of Li-ion batteries in charging, discharging and assembly before use. the batteries very sensitive to charging characteristics and may explode or burn if mishandled.
#Smok xpro bt50 how to
Note: please ensure you have basic knowledge on how to properly use it.ġ)users need to pay attention to Li-ion cells when vaping. Mode: Variable wattage and mechanical mod.Material: Aluminium alloy and zinc alloy.Can charge from the micro USB port directly High-temperature protection, short circuit protection, discharge protectionħ. DC-DC flat signal, spring-loaded brass pinĦ. Support resistance of atomizer from 0.2ohm to 4.0ohmĤ. Working wattage from 6w to 50w( upgraded to 65w now)ģ.
0 kommentar(er)
